For sale is a Yuasa Tool Post Holder 740-300 will need to be milled to fit your lathe and 5 holders two # 301 holds up to 3/4" bits, # 341 Holds 1"diameter, #305 Holds a 3mt taper, #310 Knurling. All are (NOS) and will need to be cleaned and oiled all have packing grease on them. Please view all pics as they are part of the description. I try to describe most of the items to the best of my ability, there are times when hubby inserts info onto a Post-It-Note that you will see in the pics. Please view all pics, as they are part of the description, this also applies to my "odds & ends" and ...

For sale is a Yuasa Tool Post Holder 740-400 will need to be milled to fit your lathe and 5 holders two # 402 holds up to 1" bits, # 404 Holds 1"diameter, #405 Holds a 3mt taper, #441 Hold 1-1/4 diameter. All are (NOS) and will need to be cleaned and oiled all have packing grease on them. Please view all pics as they are part of the description. I try to describe most of the items to the best of my ability, there are times when hubby inserts info onto a Post-It-Note that you will see in the pics. Please view all pics, as they are part of the description, this also applies to my "odds & ...

The pictures show all that is included and the condition so please look close. Please see my other auctions for more tools items from a local estate. I tried to take photos of the parts that came with it. PLEASE SEE THE PHOTOS FOR THE BEST DESCRIPTION. PLEASE KNOW THAT I TRY TO SATISFY ANY AND ALL OF MY CUSTOMERS. I ANSWER ALL EMAILS AND WILL TRY TO WORK WITH YOU AS BEST I CAN. I WILL, HOWEVER, NOT BE BULLIED OR BLACKMAILED.   

Southbend Turret tool post with lever mechanism, i think this is for use with the double tool cross slides but i do not have one to see if it mounts to one or not. Be sure to view our other items for more great tooling finds.   

For sale is a Rapid I. Quick Change Tool Post, TIPO-M, dirty/tarnished from age/use. There are some pieces missing to the tool post (see pics). Includes 3 Tool Holders and a Boring Tool Holder (missing parts, see pics). Please view all pics as they are part of the description. I try to describe most of the items to the best of my ability, there are times when hubby inserts info onto a Post-It-Note that you will see in the pics. Please view all pics, as they are part of the description, this also applies to my "odds & ends" and "Lot of" items, as it is too time-consuming to describe...

THE BLOCK TURNS AND LOCKS DOWN LIKE IT SHOULD. THE MOUNT HOLES ON THE BOTTOM ARE 3 1/8 APART O. THE CENTER STUD IS 1 5/8 X 1/8H APPROX. THE DISTANCE FROM THE BOTTOM OF THE BASE PLATE TO THE CENTER OF THE SLOT FOR THE TOOL HOLDER IS 2 3/4 APPROX. THE SLOT FOR THE TOOL IS 11/16 APPROX. THERE ARE A COUPLE RUSTY SPOTS ON IT THE ASSEMBLY. ONE SET SCREWS IS MISSING ON THE BLOCK. THERE ARE MEASUREMENTS IN THE PICTURES. CHECK OUT MY OTHER LISTINGS. NO WARRANTIES GIVEN OR IMPLIED. International Buyers - Please Note. I do not mark merchandise values below value or mark items as "gifts" - US and ...

For sale is a used Aloris CA Wedge Tool Post, in good usable condition, moves smoothly. T-Nut measures approx 3-1/8 wide x. 475 thick at bottom, 1-3/4" wide x 3/8" at top. Includes 8 Holders, 5 are CA2, 1 is a CA4, 1 is a CA8, 1 is a CA12. All the holder set screws and adjust nuts have been cleaned and oiled and move freely. Please view all pics as they are part of the description. I try to describe most of the items to the best of my ability, there are times when hubby inserts info onto a Post-It-Note that you will see in the pics. Please view all pics, as they are part of the ...

4-D-M Machine 100 quick change tool post lathe tool holder Machinist Shop. Comes with a T-slot nut and a homemade aluminum spacer. The nut has some harmless surface rust. I don't see anything obviously wrong with the quick change post other than the scuffs and nicks typically found on used machine tooling of this nature.   

THE BLOCK TURNS AND LOCKS DOWN LIKE IT SHOULD. THE MOUNT HOLES ON THE BOTTOM ARE 3 1/8 APART O. THE CENTER STUD IS 1 5/8 X 1/8H APPROX. THE DISTANCE FROM THE BOTTOM OF THE BASE PLATE TO THE CENTER OF THE SLOT FOR THE TOOL HOLDER IS 2 3/4 APPROX.   

THE BLOCK TURNS AND LOCKS DOWN LIKE IT SHOULD. THE MOUNT HOLES ON THE BOTTOM ARE 3 1/8 APART O. THE CENTER STUD IS 1 5/8 X 1/8H APPROX. THE DISTANCE FROM THE BOTTOM OF THE BASE PLATE TO THE CENTER OF THE SLOT FOR THE TOOL HOLDER IS 2 3/4 APPROX.