Ed on lathes which turning diameter is from 300mm to 500mm. C06236, MATE360, C6240, Yangzhou Super C6241, C6246, etc. To select a right tool post for your lathe, swing over bed is not the only data to refer. Also need to know your lathe tool top slide width and lathe main motor power. For a light duty bench lathe with 360mm(14) swing and main power less than 3KW, a smaller model E5 might be OK for work. For a middle or heavy. Duty lathe with same 360mm(14) swing and main power more than 3KW, model B2 should be better. This B2 set is standanrd kit. 1x B2 tool post &locking wrench. ...

   Although the ad from Rutland says the toolpost is for 10-15 inch lathes, it was obviously too small for my 14-inch as the previous owner had installed a riser plate underneath it. I would recommend that this equipment be used on lathes 12-inches and smaller similar to an Aloris AXA. One(1) 40-position toolpost w/tightening wrench. One(1) Mounting stud (3/4-inch diameter, 16 tpi, approximately 6-inches long) and flange approximate dimensions 2.25 x 2.5 x 5/8 with two(2) 0.25 x 0.375 x 2.5 inch rabbets. Note: Does not include nut. Three(3) 3/4-inch capacity turning and facing holders. ...

   Quick Change Tool Post Sets for Unimat DB200 and SL1000. Tired of shimming your tool bit to get the right height for your tool bits? Long set up time to switch from one tool bit to another? QCTP was designed specifically for Unimat DB200/SL1000 lathe. The set comes with five tool holders to hold 1/4" tool bits, 5/16" tool bits, 3/8 diameter boring bar. Cut Off Tool Holder to hold 1/16" X 3/8" Cut Off Blade and. A Dremel holder for 300 Series Dremel. Raising block is included to raise the tool post by 20.0 mm. 787 to accommodate lathe with a head rising block. T' nut to mount the ...

T 51 QUICKCHANGE TOOL HOLDER. THIS LISTING IS FOR 4 HOLDERS. SPARE HOLDER FOR QUICK CHANGE. WILL TAKE A 16MM TOOL BUT MAY PUT YOU ABOVE CENTRE. KNOWN AS A T1 TOOLHOLDER. USED ON MACHINES LIKE BOXFORDS AND SMALL HARRISONS. PLEASE HAVE A LOOK AT OUR 8500 OTHER ITEMS. The item "RDGTOOLS 4 X T51 T1 QUICKCHANGE TOOLPOST HOLDERS BOXFORD SIZE QUICK CHANGE" is in sale since Tuesday, November 26, 2019. This item is in the category "Business, Office & Industrial\Industrial Tools\Other Industrial Tools". The seller is "rdg355" and is located in YORKSHIRE. This item can be shipped worldwide. ...

   XA Piston Type Quick Change Tool Post 6PCS Include #1 250-201XL #2 250-202XL Oversize Tool Holders. Suitable for lathe center height 0.7-2.2 (top compound surface to lathe center line). 13" , 14" & 1307 , Delta 14" , Logan 14" Emco : Elnomat13S , Harrison : 11,12 &13", Sheldon : 11 &13" , Clausing : 1300 series, Monarch : 13 , Nardini : MS1400 MS1600, Acer : 1340 and many other import lathes. Includes: 250-200 Tool Post, 250-201XL Holder, 250-202XL Holder, 250-204 Holder, 250-207 Holder, 250-210 Holder. Set Screw Thread Size: M10x19. Increases production of lathe ...

   AXA Piston Quick Change Tool Post and Tool Holder for Lathe 6-12 250-100 Set. Suitable for lathe center height 0.6 - 1.75 (top compound surface to lathe center line). It is precision engineered to assure repetitive accuracy. No time wasted with shims. All working parts hardened and precision ground. The tool post comes with a blank T-Nut plate, the customer have to do some. Machining work to make it fit into their own specific lathe T slot. Suitable for lathe center height 0.6 - 1.75 (top compound surface to lathe center line) , such as. South Bend 9 & 10 , Atlas 10 & 12, ...

T 51 QUICKCHANGE TOOL HOLDER. THIS LISTING IS FOR 3 HOLDERS. SPARE HOLDER FOR QUICK CHANGE. WILL TAKE A 16MM TOOL BUT MAY PUT YOU ABOVE CENTRE. KNOWN AS A T1 TOOLHOLDER. USED ON MACHINES LIKE BOXFORDS AND SMALL HARRISONS. PLEASE HAVE A LOOK AT OUR 8500 OTHER ITEMS. The item "RDGTOOLS 3 X T51 T1 QUICKCHANGE TOOLPOST HOLDER BOXFORD SIZE QUICK CHANGE" is in sale since Tuesday, November 26, 2019. This item is in the category "Business, Office & Industrial\Industrial Tools\Other Industrial Tools". The seller is "rdg355" and is located in YORKSHIRE. This item can be shipped worldwide. ...

T 51 QUICKCHANGE TOOL HOLDER. SPARE HOLDER FOR QUICK CHANGE. WILL TAKE A 16MM TOOL BUT MAY PUT YOU ABOVE CENTER. KNOWN AS A T1 TOOLHOLDER. USED ON MACHINES LIKE BOXFORDS AND SMALL HARRISONS. PLEASE HAVE A LOOK AT OUR 3700 OTHER ITEMS. The item "RDGTOOLS T51 T1 QUICKCHANGE TOOLPOST HOLDER BOXFORD SIZE QUICK CHANGE" is in sale since Tuesday, August 19, 2014. This item is in the category "Business, Office & Industrial\Industrial Tools\Other Industrial Tools". The seller is "rdg355" and is located in YORKSHIRE. This item can be shipped worldwide. Non-Domestic Product: No Modified Item: No...

Dorian Tool Post, Quick Change, SDN30,13-15 In - SDN30BXA. This toolpost and holder are in very good, useable condition. The holder has some surface rust and the toolpost dies not have the center bolt and sliding t nut. The item "Dorian Tool Post, Quick Change, SDN30,13-15 In SDN30BXA" is in sale since Tuesday, January 28, 2020. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Workholding & Toolholding\Toolholding\Quick Change Tool Post". The seller is "sincityfabricationofky" and is located in Arlington, Kentucky. This item can be shipped ...

   New AXA Size 250-111 Set Wedge Type Quick Change Tool Post Set for 6-12 Lathe. 250-111 Wedge Type Tool Post. 250-101 Turning Tool Holder , use tool bit up to 1/2. 250-102 Boring, Turning Tool Holder, use tool bit up to 1/2" and round shank tool bits up to 7/16". 250-104 Heavy Duty Boring Bar Holder, use 5/8 and 3/4 shank boring bars. 250-107 Parting Blade Tool Holder, use 1/2 high parting blades. 250-110 Knurling and Turning Tool Holder. Plenty of working positions for more tool holder. Adjust height of cutting edge easily and accurately. Turning and facing tools can be locked ...